Heater Specs | Richmond 5v40-7 Water

A: No. This unit is not certified for mobile/manufactured home use. Look for “MH” designation in model number. Final Thoughts The Richmond 5V40-7 is a straightforward, no-frills natural gas water heater. Its specs—40 gallons, 38k BTU, 0.62 UEF, and 58-inch height—make it a common choice for replacing older tanks in homes with traditional venting. While it lacks energy-saving features like electronic ignition or extra insulation, its low upfront cost and simplicity are its main selling points.

A: The “-7” revision often includes an updated gas control valve (electronic ignition in some cases) or a revised draft hood. Check the manual. Most parts are interchangeable. richmond 5v40-7 water heater specs

Before purchasing, confirm your vent size (3-inch required), gas pressure, and clearance space. If your home has higher hot water demand (more than 3 people), consider moving up to a 50-gallon model like the Richmond 6V50-7. But for a budget-friendly, direct replacement of a failing 40-gallon natural gas tank, the 5V40-7 gets the job done. Always consult a licensed plumber or gas fitter before installing a gas water heater. Local building codes may require permits and professional installation. Final Thoughts The Richmond 5V40-7 is a straightforward,

Note: If your model is older than 2015, the EF will be listed. Newer production runs of the 5V40-7 use UEF. | Specification | Detail | |---------------|--------| | Fuel Type | Natural Gas (NG) – Not convertible to LP without a certified kit | | Input BTU/hr | 38,000 BTU (some models: 40,000 BTU – check rating plate) | | Burner Type | Single atmospheric burner | | Gas Inlet Size | 1/2" NPT | | Manifold Pressure | 3.5" W.C. (natural gas) | | Minimum Gas Supply Pressure | 5.0" W.C. | | Maximum Gas Supply Pressure | 10.5" W.C. | 4. Venting Specifications (Critical) | Specification | Detail | |---------------|--------| | Vent Type | Type B (double-wall) or single-wall metal vent | | Vent Diameter | 3 inches | | Draft Hood | Included (integral) | | Maximum Vent Run | 20 feet horizontal run; unlimited vertical with proper draft | | Clearance to Combustibles | 6 inches (sides), 12 inches (front for service) | A: The “-7” revision often includes an updated

This article provides an exhaustive deep dive into the , including performance data, physical measurements, warranty information, and common replacement considerations. Overview: What is the Richmond 5V40-7? The Richmond 5V40-7 is a 40-gallon natural gas water heater designed for standard residential use. It is part of Richmond’s “Essential” or builder-grade series, offering a balance between affordability and functionality. The “5V” designation typically indicates the venting type (atmospheric draft) and series, while “40” denotes the tank capacity, and “7” often refers to specific burner or revision details.

A: No. The gas valve and pilot operate without any electrical connection. This makes it ideal for use during power outages.

Suitable for homes with 2-4 people, providing hot water for showers, dishwashers, laundry, and sinks. Full Technical Specifications (Richmond 5V40-7) Below is a complete list of specifications based on manufacturer data and compliance standards (DOE, ANSI Z21.10.1). 1. Tank & Capacity | Specification | Detail | |---------------|--------| | Nominal Capacity | 40 Gallons (151.4 liters) | | Actual Storage Volume | 38–40 gallons (varies slightly by dip tube) | | Tank Material | Vitraglas® enamel-lined steel (porcelain coating) | | Anode Rod | Magnesium (sacrificial) – 3/4" NPT access | 2. Energy Performance | Specification | Detail | |---------------|--------| | Energy Factor (EF) | 0.59 (pre-2015 standard) / UEF: 0.62 (Uniform Energy Factor) | | First Hour Rating (FHR) | 67 gallons | | Recovery Rate | 38.8 gallons per hour (at 90°F rise) | | Standby Heat Loss | ~4-5% per hour (typical for standard tank) |