Phico D0 94v0 Lcd Display Datasheet Pdf [portable] -
| Pin No. | Symbol | Level | Function | | :---: | :---: | :---: | :--- | | 1 | VSS | 0V | Ground | | 2 | VDD | +5V | Logic Power Supply | | 3 | V0 / VEE | Variable | Contrast Adjustment (via potentiometer to VSS) | | 4 | RS | H/L | Register Select: 0=Command, 1=Data | | 5 | R/W | H/L | Read/Write: 0=Write, 1=Read (often tied to GND) | | 6 | E | H→L | Enable signal (falling edge triggered) | | 7 | DB0 | H/L | Data Bus Bit 0 (LSB) – not used in 4-bit mode | | 8 | DB1 | H/L | Data Bus Bit 1 | | 9 | DB2 | H/L | Data Bus Bit 2 | | 10 | DB3 | H/L | Data Bus Bit 3 | | 11 | DB4 | H/L | Data Bus Bit 4 (MSB of low nibble in 4-bit mode) | | 12 | DB5 | H/L | Data Bus Bit 5 | | 13 | DB6 | H/L | Data Bus Bit 6 | | 14 | DB7 | H/L | Data Bus Bit 7 / Busy Flag | | 15 | LED_A | +5V | Backlight Anode (Power for backlight) | | 16 | LED_K | GND | Backlight Cathode (Ground for backlight) |
| Command | Hex Code | Description | | :--- | :--- | :--- | | Clear Display | 0x01 | Clears screen, returns cursor to home | | Return Home | 0x02 | Returns cursor to home (DDRAM address 0) | | Entry Mode Set | 0x06 | Increment cursor, no shift | | Display ON/OFF | 0x0C | Display ON, Cursor OFF, Blink OFF | | Display ON (with cursor) | 0x0E | Display ON, Cursor ON (underscore) | | Function Set (8-bit) | 0x38 | 8-bit, 2 lines, 5x8 dots | | Function Set (4-bit) | 0x28 | 4-bit, 2 lines, 5x8 dots | | Set DDRAM Address | 0x80 + addr | Set cursor to position (e.g., 0x80 = line 1, col 0) | phico d0 94v0 lcd display datasheet pdf
| Parameter | Typical Value for PHICO D0 Series | | :--- | :--- | | | 16 Characters x 2 Lines (16x2) | | Display Type | STN (Super Twisted Nematic) or FSTN | | Polarizer Mode | Transflective (readable in sun & via backlight) | | Viewing Direction | 6 o'clock (or 12 o'clock – check datasheet) | | Backlight | Yellow-Green or White LED (parallel or series) | | Controller | KS0066 or S6A0069 (HD44780 compatible) | | Interface | 4-bit or 8-bit parallel (14+2 pins) | | Operating Voltage | 4.5V to 5.5V (typically 5.0V) | | Logic Supply Current | 1.0 mA (typical without backlight) | | Backlight Current | 120-200 mA (depends on color) | | Duty Cycle | 1/16 duty, 1/5 bias | | Operating Temp | 0°C to +50°C (Standard) / -20°C to +70°C (Extended, if specified) | Part 3: The Essential Pinout (Without the Datasheet) Most PHICO 94V-0 displays use the standard 16-pin header configuration (0.1-inch pitch). Here is the pinout you will likely find in the datasheet PDF: | Pin No