Aspeed Ast2500 Datasheet New Here
| Parameter | Specification (New Revision) | Notes | | :--- | :--- | :--- | | | ARM926EJ-S, 32-bit RISC | 384KB L2 Cache | | Max Frequency | 400 MHz (Standard) / 800 MHz (Overdrive mode) | Overdrive requires enhanced cooling | | Operating Voltage | 3.3V I/O, 0.9V Core, 1.8V DDR4 | New: Absolute max input on ADC: 1.8V | | Integrated Video | 2D Graphics Engine, 1920x1200@60Hz | 256MB DDR4 frame buffer | | Host Interfaces | PCIe Gen2 (x1, dual root), eSPI, LPC 1.0 | New: eSPI is preferred for Z690/C621 chipsets | | Peripheral IF | 2x GbE MAC, 6x UART, 2x SPI, 1x SD/SDIO, 8x PWM | New: SPI clock speed maxed at 100MHz | | Temperature Range | 0°C to 70°C (Commercial) or -40°C to 105°C (Industrial) | Check suffix: -IR for industrial | | Package | 484-pin LFBGA, 19x19mm | 0.8mm pitch | Part 4: How to Interpret the "New" Datasheet for PCB Layout Searching for the "aspeed ast2500 datasheet new" is often a cry for help during PCB layout debugging. Here are three critical layout rules derived from the latest document: Rule 1: Strap Pins are Volatile The new datasheet dedicates an entire chapter to "Strapping Resistors." The AST2500 reads the state of certain pins (e.g., SCL0 , SDA0 ) at power-on to determine boot order. New warning: Placing capacitors larger than 10pF on these lines will delay the strap sampling, causing random boot failures. Rule 2: USB 2.0 Phy Layout The built-in USB 2.0 OTG PHY is notoriously sensitive. The new revision provides exact length matching: D+ and D- traces must be within 0.5mm of each other and kept under 200mm total. Violating this leads to "Device Descriptor Failed" errors. Rule 3: VGA DAC Termination For the analog VGA output (RGB), the new datasheet includes a reference schematic for 75-ohm termination using a THS7316 driver. It now explicitly states that direct connection to a VGA port is not supported without this buffer. Part 5: Comparing the AST2500 to Modern Alternatives (Why Still "New"?) You might wonder: If the AST2600 exists, why are people searching for a "new" AST2500 datasheet?
Before spinning your next PCB, create an account on ASPEED’s website. Download Revision 1.6 or higher. Pay special attention to Section 4 (Power Sequencing) and Appendix C (Errata). Your future debug time depends on it. Disclaimer: Specifications are based on publicly available ASPEED documentation as of late 2024. Always consult the official datasheet for final design decisions. aspeed ast2500 datasheet new
While the newer AST2600 chip has grabbed headlines with its dual-core Cortex-A7 architecture, the remains the gold standard for cost-sensitive, power-efficient, and highly stable platforms. If you are searching for the "aspeed ast2500 datasheet new," you are likely either an engineer validating a legacy refresh, a procurement specialist verifying late-lifecycle specs, or a developer looking for the latest errata. | Parameter | Specification (New Revision) | Notes
Do not assume that a datasheet you downloaded in 2019 is still valid. The latest revisions fix PCIe training issues, redefine voltage tolerances for modern chipsets, and add critical security lockdown procedures. Rule 2: USB 2
| Feature | AST2500 (New Datasheet) | AST2600 | | :--- | :--- | :--- | | | ARM926 (Single core) | Dual Core Cortex-A7 | | Power Consumption | ~4W | ~8W | | PCIe | Gen2 | Gen3 | | Video | 2D only | 3D acceleration | | Cost (1000 units) | ~$12 USD | ~$28 USD | | Ideal Use | Storage JBOD, Routers, Legacy servers | Cloud-scale AI servers |