| Parameter | Symbol | Test Condition | Min | Typ | Max | Unit | |-----------|--------|----------------|-----|-----|-----|------| | Input Voltage | VIN | – | 2.0 | – | 6.0 | V | | Output Voltage | VOUT | Fixed option | 3.267 | 3.3 | 3.333 | V | | Output Current | IOUT | – | 0 | – | 300 | mA | | Dropout Voltage | VDROP | IOUT = 200 mA | – | 120 | 180 | mV | | Quiescent Current | IQ | No load | – | 25 | 50 | µA | | Shutdown Current | ISD | EN = GND | – | 0.1 | 1 | µA | | Line Regulation | ΔVOUT / ΔVIN | VIN = (VOUT+1) to 6V, IOUT=10mA | – | 0.05 | 0.2 | %/V | | Load Regulation | ΔVOUT / ΔIOUT | IOUT = 1 to 250 mA | – | 0.1 | 0.5 | % | | Power Supply Ripple Rejection | PSRR | f = 1 kHz, IOUT = 100 mA | – | 65 | – | dB | | Thermal Shutdown | TSD | – | 150 | 160 | 170 | °C | If the 8681L is an LDO, the pinout will typically be:
| Pin # | Name | Description | |-------|------|-------------| | 1 | VIN | Unregulated input voltage | | 2 | GND | Ground | | 3 | EN | Enable control (active high) | | 4 | NC | No connect (or bypass cap pin) | | 5 | VOUT | Regulated output voltage | 8681l ic datasheet
ΔT = P * θJA = 0.51 * 250 = 127.5°C At 25°C ambient, TJ = 152.5°C → (125°C). Solution: Use a lower input voltage, reduce current, or switch to a larger package like SOT-89. Part 6: Common Mistakes When Using the 8681L Datasheet Even with the official datasheet, engineers make avoidable errors. Here are the top 5: 6.1 Ignoring the "Minimum Load Current" Some older regulator designs require a minimum load (e.g., 1 mA) to maintain regulation. If your load is intermittent, add a dummy resistor. Check the datasheet's "Minimum Load Current" spec. 6.2 Wrong Capacitor Type or Value The datasheet often specifies "ceramic X5R or X7R." Using an electrolytic or a cheap Y5V can cause oscillations. Also, check the ESR range – some LDOs require an output capacitor with ESR between 0.1Ω and 1Ω. 6.3 Misreading the Pinout (Especially for SOT-23) SOT-23-3 and SOT-23-5 have different orientations. The datasheet typically shows a top view (pins facing down, from above). A common mistake is to mirror the pinout. 6.4 Floating the Enable Pin If the 8681L has an EN pin and you leave it floating, the internal state is undefined. The device may remain off or oscillate. Always tie EN to VIN or a logic high. 6.5 Exceeding Input Voltage Even Briefly Many "6V max" LDOs will fail at 6.2V. If your supply is a 5V USB that can spike to 5.5V, you are safe. But if you use a 9V wall adapter, the 8681L will be destroyed instantly. Part 7: Comparing 8681L With Alternative ICs When you review the 8681L datasheet, compare it with these common alternatives to see if it is the right fit. | Parameter | Symbol | Test Condition |
While this guide has provided an educated framework for understanding the 8681L (assuming it is a low-dropout regulator), Never trust a pinout or maximum rating from a forum or an AI model alone. Here are the top 5: 6